Shop
-
Broen-Lab Two Way Straight Lift & Turn Gas Tap
£68.68 + VATBROEN-LAB two way 180 degree lift & turn gas tap
-
Belfast Lab Sink 595mm x 460mm x 250mm
£172.50 + VATEnamel Glazed Laboratory Sink 595mm x 460mm x 250mm
Integral Overflow
Hard wearing, durable, alkali and acid resistant
-
Brownall Fixed Swanneck CW Tap Wrist Action Levers
£95.33 + VATThis tap is available with the following optional extras:
-
Brownall Special Water Pillar Tap
£176.30 + VATPillar angle fitting with 10 x 1,5 mm OD LLDPE (Linear Low-Density Polyethylene) tube protected by a brass pipe.
-
Vulcathene Large Glass Dilution Trap – 38mm
£371.96 + VATVulcathene Glass Dilution Recovery Trap ( 1 -1/2″ BSP Connection )
Volume 2.3 litres
-
Fireclay Lab Sink 330mm x 330mm x 180mm
£142.00 + VATEnamel Glazed Laboratory Sink 330mm x 330mm x 180mm
Hard wearing, durable, alkali and acid resistant
Fixing clips available
-
Broen-Lab Mixer Tap with Wrist Action Levers
£189.63 + VATThis tap is supplied with aerator nozzle but the following alternatives are available if required:
-
Watersaver Swivel Single Hot Water Lab Tap, Wrist Blade Handle
£75.03 + VATSingle Water Tap, Bench Mounted with wrist action handle. The tap comes with a serrated nozzle, if you require an aerator nozzle instead or if you need a Pipe Interrupter to prevent backflow please select from below.
-
Bench Mounted Eye Wash
£233.90 + VATBench mounted eye wash
Movable laboratory emergency spray deck-mounting single head
-
Brownall Swivel Swanneck Cold Water Tap
£81.23 + VATThis tap is available with the following optional extras:
-
200mm PVC 90 Deg Elbow
£44.77 + VAT- Internal Diameter: 200mm
- Colour: Grey
- See below for other sizes relevant to drawing
-
Epoxy Resin Multi Fit Sink – S25 456mm x 380mm x 216mm deep
£172.00 + VATA standard range of epoxy resin sinks and troughs are moulded complete with a fixing flange in order to simplify fitment and to optimise the integrity of the joint with the worktop.
An overhang (underslung) sink is bonded and screwed to the underside of a worktop with the worktop slightly overhanging the sink opening. This type of fitment is also commonly referred to as ‘underslung’. This fitment is adequate for many general laboratory applications.
The base of the sink slopes to a hole rebated to accept a waste fitting.
Sinks can also be drilled to accept an overflow fitting.
-
Vulcathene Spanner – 38mm
£24.76 + VATFor 38mm Fittings
This moulded polycarbonate spanner is made specifically for use with the Vulcathene Mechanical range and should always be used to tighten the Vulcathene nuts as it will not distort or damage the nuts in the process of achieving a secure joint
-
Vulcathene Groove Cutting Tool – 38mm
£81.66 + VATFor 38mm Tube
The vulcathene grooving tool enables a groove of exact depth and width to be
cut in the correct location from the end of the pipe where mechanical olive is located.
-
Wall Mount Double Eye Wash
£250.87 + VATWall mounted double eye wash
Wall mounted eye shower with a two 45° angled heads, incl. 1.5m inlet hose.
Trigger operated including a built-in check valve and FLOWFIX for regulation of water flow (14 l/min).
-
Brownall Fixed Swanneck HW Tap Wrist Action Levers
£95.33 + VATThis tap is available with the following optional extras:
-
Vulcathene W15 F.I. to Pipe Coupler – 38mm
£15.63 + VATVulcathene F.I. to Pipe Coupler
38mm
1 1/2″ BSP female thread
With standard BSP parallel threads the W15 pipe coupler can be screwed directly to M.I. ends of metal or plastic pipes.
The 38mm unit can be screwed to the threaded tail of a waste or drip cup when a pipe connection is required
-
Epoxy Resin Drop on Sink – SGL10-DO 400mm x 400mm x 300mm deep
£226.40 + VATDrop-on sinks are designed to be easily fitted to any type of worktop material.
They have self-rimming flanges which will conceal the core layer of a laminated worktop.
The sink is self-supporting on its integral flange and can be bonded in place with silicone sealant or Epoxy Resin grout.
The same raised flange has a smooth 45 face to the outside that will allow the user to wash liquids over it but prevent accidental spillage of materials into the sink.
The base of the sink slopes to a hole rebated to accept a waste fitting. Sinks can also be drilled to accept an overflow fitting.
-
Polypropylene Lab Sink 418mm x 316mm x 220mm
£69.00 + VAT- High Quality Polypropylene Sink
- Temperature range: 0-80°C
- Self-draining base
- Standard colour: Black
- Extremely durable.
-
Table Mount Single Eye Wash
£224.99 + VATTable Mount Single Eye Wash
Table mounted eye shower with a single 45° head, incl. 1.5m inlet hose.
Trigger operated including a built-in check valve and FLOWFIX for regulation of water flow (7 l/min).
-
200mm PVC Socket
£23.66 + VAT- Internal Diameter: 200mm
- Colour: Grey
- See below for other sizes relevant to drawing
-
Fixed Swanneck Outlet
£28.35 + VATFixed swan neck cold water outlet with fixed serrated nozzle
All brass construction
Plastic coated ( Rilsan )
Standard colour Light Grey
3/8″ BSP x 60mm flat ended brass shank with backnut
Overall height 280mm
Height from tip of outlet to bench 200mm
-
Vulcathene Small Oval Drip Cup
£37.40 + VATVulcathene Small Oval Drip Cup ( 1 -1/2″ BSP Connection )
Length 178mm x Width 102mm
Height 216mm
-
160mm PVC 90 Deg Elbow
£36.31 + VAT- Internal Diameter: 160mm
- Colour: Grey
- See below for other sizes relevant to drawing
-
Epoxy Resin Underslung Sink – SR12 550mm x 365mm x 250mm deep
£237.60 + VATA standard range of epoxy resin sinks and troughs are moulded complete with a fixing flange in order to simplify fitment and to optimise the integrity of the joint with the worktop.
An overhang (underslung) sink is bonded and screwed to the underside of a worktop with the worktop slightly overhanging the sink opening. This type of fitment is also commonly referred to as ‘underslung’. This fitment is adequate for many general laboratory applications.
The base of the sink slopes to a hole rebated to accept a waste fitting.
Sinks can also be drilled to accept an overflow fitting.
-
Vulcathene Large Oval Drip Cup
£40.78 + VATVulcathene Large Oval Drip Cup ( 1 -1/2″ BSP Connection )
Length 264mm x Width 111mm
Height 225mm
-
200mm PVC 45 Deg Elbow
£30.42 + VAT- Internal Diameter: 200mm
- Colour: Grey
- See below for other sizes relevant to drawing
-
Broen-Lab Fixed Hot Water Tap
£81.23 + VATThis tap is available with the following optional extras:
-
S/S Inset Sink & Drainer FP10012/13 965 X 525mm
£559.19 + VAT316 grade stainless steel offers excellent acid and chemical resistance.
Supplied with sound deadening pads and integral earth tag
Available without overflow on request
-
Epoxy Resin Drop on Sink – SDS5-DO 300mm x 200mm x 200mm deep
£122.40 + VATDrop-on sinks are designed to be easily fitted to any type of worktop material.
They have self-rimming flanges which will conceal the core layer of a laminated worktop.
The sink is self-supporting on its integral flange and can be bonded in place with silicone sealant or Epoxy Resin grout.
The same raised flange has a smooth 45 face to the outside that will allow the user to wash liquids over it but prevent accidental spillage of materials into the sink.
The base of the sink slopes to a hole rebated to accept a waste fitting. Sinks can also be drilled to accept an overflow fitting.
-
Epoxy Resin Underslung Sink – SGR11 500mm x 400mm x300mm deep
£255.20 + VATA standard range of epoxy resin sinks and troughs are moulded complete with a fixing flange in order to simplify fitment and to optimise the integrity of the joint with the worktop.
An overhang (underslung) sink is bonded and screwed to the underside of a worktop with the worktop slightly overhanging the sink opening. This type of fitment is also commonly referred to as ‘underslung’. This fitment is adequate for many general laboratory applications.
The base of the sink slopes to a hole rebated to accept a waste fitting.
-
Vulcathene 92.5 deg Loose Nut Sweep Elbow – 38mm
£19.41 + VAT38mm 92.5 loose nut sweep bend
One end has the standard nut an dolive connection whilst the other has a
captive nut for connection to threaded units.
-
Epoxy Resin Sink with Drainer SD1000
£727.20 + VATSingle bowl single drainer sink tops feature a worktop, sink and drainer which is moulded in one section and as such is totally seamless.
Sink tops incorporate a ribbed drainer area which slopes to an integrally moulded sink bowl.
This single drainer unit is cast oversize and then cut to the required size, from a minimum of 900mm x 600mm up to a maximum of 1000mm x 850mm.
They are then fitted with edging from ours standard range to make up the required configuration.
-
Wall Mounted Eye Wash
£241.02 + VATWall mounted eye wash
Emergency spray unit single head
For use in industry, laboratories and universities
-
Wall Mount Single Eye Wash
£224.99 + VATWall Mount Single Eye Wash
Wall mounted eye shower with a single 45° head, incl. 1.5m inlet hose.
Trigger operated including a built-in check valve and FLOWFIX for regulation of water flow (7 l/min)
-
Fume Cupboard Valve, Straight Face, BT753
£42.98 + VATWaterSaver Front Control Valve BT753 available for the following media:
BT753W water valve construction with compression valve cartridge = £42.98 + VAT
BT753N-AIR Needle valve construction, Non Burn = £42.98 + VAT
BT753N-VAC Needle valve construction, Vacuum = £42.98 + VAT
BT753G Push/turn gas valve construction = £52.08 + VAT
-
Stainless Steel Sink S27SR – 546 X 394 X 180 mm
£295.15 + VAT316 grade stainless steel offers excellent acid and chemical resistance.
This model is designed to be inset into the worksurface, undermounted versions available.
Supplied with sound deadening pads and integral earth tag
Available without overflow on request
-
Wall Mounted Drench Shower
£327.57 + VATWall mounted drench shower
Horizontal drench shower ABS shower head
Highly visible yellow ABS anti-corrosive plastic coating
-
110mm PVC 90 Deg Elbow
£27.88 + VAT- Internal Diameter: 110mm
- Colour: Grey
- See below for other sizes relevant to drawing
-
Brownall / Broen Aerator Nozzle
£18.45 + VATAerator nozzle & adapter for water. M19x1 inlet.
Fits the Brownall / Broen range of water taps after removing the serrated nozzle.
-
Fume Cupboard Valve, Straight Face, BT751
£42.98 + VATWaterSaver Front Control Valve BT751 available for the following media:
BT751N-AIR Needle valve construction, Non Burn = £42.98 + VAT
BT751N-VAC Needle valve construction, Vacuum = £42.98 + VAT
BT751G Push/turn gas valve construction = £52.08 + VAT
BT751FCN Fine control needle valve construction (cleaned, lubricated and packaged for high purity gas service) = £65.97 + VAT
-
Fume Cupboard Valve, Straight Face, BT750
£47.95 + VATWaterSaver Front Control Valve BT750 available for the following media:
BT750W water valve construction with compression valve cartridge = £47.95 + VAT
BT750N-AIR Needle valve construction, Non Burn = £47.95 + VAT
BT750N-VAC Needle valve construction, Vacuum = £47.95 + VAT
BT750G Push/turn gas valve construction = £57.05 + VAT
BT750FCN Fine control needle valve construction (cleaned, lubricated and packaged for high purity gas service) = £70.94 + VAT
-
Polypropylene Lab Sink 558mm x 355mm x 240mm
£77.50 + VAT- High Quality Polypropylene Sink
- Temperature range: 0-80°C
- Self-draining base
- Standard colour: Black
- Extremely durable.
-
200mm PVC Pipe – 6m
£209.53 + VAT- 6 metre length PVC pipe
- Outside Diameter: 200mm
- Wall thickness: 2.5mm
- Colour: Grey
-
Vulcathene W14 M.I. to Pipe Coupler – 38mm
£15.63 + VATVulcathene M.I. to Pipe Coupler
38mm
1 1/2″ Male thread
With standard BSP parallel threads the W14 Pipe Coupler can be screwed direct into the F.I. fittings
of metal or plastic pipes
-
Laboratory Posture Stool with small back support
£102.75 + VATHeight adjustment 580-800mm
Colour: BLACK
